Classic AutoAir Perfect Fit-Elite Series Operations Instructions

1 “PERFECT FIT SERIES” IN-DASH HEAT/ COOL/ DEFROST 1969-70 MUSTANG CONTROL & OPERATING INSTRUCTIONS The controls on your new “Perfect Fit” sys

10 Locate the Inlet Block off Plate. Located above glove box opening place block off plate over the hole. Attach with (2) #10 x ¾ “ hex washer he

11 Locate in the hardware sack kit the evaporator Support Bracket. Attach bottom end of the bracket to the (2) 1/8” Dia. holes in front of the evap

12 Locate the Defrost / Heat Duct Assembly. Attach to evaporator using (2) #10 x 5/8 pan head Philips screws. Be sure that the S-clips are presse

13

14 Secure ground from the electronic actuator and the blower motor using (2) #10 x ¾“ hex washer head Tek screw. REFER TO THE WIRING DRAWING ON PA

15 Route shortest of (2) cables and attach to the defrost / heat duct. Insert cable into second hole from the bottom. Attach using (1) #10 x 5/8”

16 Locate Defrost Air Duct lay on table and mark a line 4” from the top lip as shown. Cut off lower part of the duct And discard. Locate in

17 Route over the face duct and attach to the hose adaptors as shown. Locate the 2 ½” dia flex hose (1) piece 3’ long and attach it to outlet beh

18 Locate the Template on page 27 of instructions. Carefully cut Template as described. Carefully tape template from the bottom edge and center o

19 Locate in the Hardware Sack Kit the Center Louver. Insert louver through the cut hole. Using a straight edge carefully insert between the lou

2 CAUTION: ALL OF THE OUTSIDE VENTS MUST BE CLOSED WHEN THE SYSTEM IS IN THE A/C MODE. THIS WILL ALLOW THE A/C SYSTEM TO FUCTION AT ITS MAXIMUM PERFO

20 Located on page 29 & 31 of instructions the driver and passenger louver template. On drivers side follow instructions on template and attac

21 Locate in the Condenser kit the Drier, Drier Mounting bracket, pressure switch kit, Liquid Tube, (2) #10 tek screws, and (2) #6 o-rings. To lo

22 Located on the drivers side radiator support is a knockout in the sheet metal. There are (2) dimples these are the locators for the hole cutout.

23 Locate the tube support clamp assembly and attach to the tubes as shown. Slide Condenser Assembly into place as shown. Insert the tube

24 Locate the long Liquid Hose. This hose has a Straight and a 45 Degree Fitting pre crimped into position. Loosely attach the straight end of th

25 Locate female bullet connector that is supplied with the Hi-Low pressure switch. Cut one of the white wires from the pressure switch. Attach bull

26 The other end will attach to the firewall. Use (2) #10 o-rings and a few drops of mineral oil. Ty-rap liquid hose to the spring tower

27 IMPORTANT CAUTION: WATER VALVE MUST BE INSTALLED PER THE INSTRUCTIONS. Classic Auto Air has done extensive testi

3 INSTALLATION INSTRUCTIONS 1969-70 MUSTANG Congratulations! ! You have just purchased the highest quality, best performing A/C system ever designed

4 Remove Glove box, Passenger Fascia, and Padded Dash Cover Retain original hardware. See below for screw locations. Remove radio mounting

5 Removal of the control head requires disconnection of the Mode Control cable. This is located below the defrost duct. The Temperature Cont

6 Locate blower motor on the firewall (Passenger Side) in engine compartment. Remove 5 nuts around blower. Also disconnect electrical connector fro

7 Pull lower edge of the dash towards the rear of car to allow clearance for the heater assembly. Remove complete Heater Assembly and discard.

8 Locate original wiring harness that was connected to original blower switch. From the plug cut the YELLOW wire and attach a ¼” insulated male spa

9 Locate knob in control sack kit and install over switch shaft. Locate in the control sack kit (2) cables. Longest one is for th